HoldPeak HP 1320/1500 D:S 30:1 Digital IR Thermometer Non Contact Laser Infrared Temperature Instrument Pyrometer 50 1500'C

HoldPeak HP 1320/1500 D:S 30:1 Digital IR Thermometer Non Contact Laser Infrared Temperature Instrument Pyrometer 50 1500'C
  • Продавецwww.tampabaybuccaneersvsminnesotavikings.us
  • Список ценUS $45.51piece
  • Продажная ценаUS $45.51piece
  • ДоставкаБесплатная доставка
  • Рейтинги4,6 (126)

Oписание продукта

SW-LDS50A Deep Tawet Laser Rangefinder Module Measuring Instrument Industry 50 Meters Distance Sensor

Product Display_

HTB1GZOVnC8YBeNkSnb4q6yevFXahHTB1pGvlhEOWBKNjSZKzq6xfWFXabHTB13mMUhrZnBKNjSZFrq6yRLFXayHTB1.Zp9nsyYBuNkSnfoq6AWgVXaYHTB1cUxIv_JYBeNjy1zeq6yhzVXa4

 

HTB1Zv97h8yWBuNkSmFPq6xguVXad_

HTB1YWW_vNSYBuNjSsphq6zGvVXarProduct Features_

 

1, measurement range: 0.05-50M, precision 2mm

2 "configuring Rs232/485 industrial interface

3 "aluminum alloy shell, sturdy, 4 azimuth loading, satisfied

Various measurement site, shell waterproof grade |P67

4 "high precision hardware and software design, outdoor use of lightning protection

5 "dial up networking support, 64 groups at the same time use

 

technical parameter

Model SW-LDS50A operation mode single data continuous data external trigger

Measuring distance 0.05m-50m connector 9 PIN socket

Minimum display unit 1mm data interface RS485/RS232

The measurement accuracy (2 + 1 + 1 "(1*5 5/10000) * 8-12V power supply

Data output rate 2HZ (customizable) power 1.5W

Type Class / 635nm laser | less than 1MW storage temperature range of -20 DEG C-60 DEG C

Indicator light red laser working temperature range 0 degree C-40 C

Protection level IP67 storage humidity RH85%

Shell model SW-LDS50A material die casting aluminum alloy

Shape size 118*73*30mm

Operation mode single data continuous data external trigger

Connector 9 PIN socket

Data interface RS485/RS232

Power supply 8-12V

Power consumption 1.5W

Storage temperature range -20 [C-60] C

Storage humidity RH85%

 

 

 

The use of this tool software:

(1) all the instruments are connected in series through the twisted pair line, and then the RS485/RS232 is converted to the joint to connect them to the computer.

The software is controlled by serial port, if the computer has no serial port. Only USB, can be pre - USB/RS232 converter;

I - select the serial port connected by the instrument. Then select RWI,

The time of the computer polling sensor can be adjusted, and the value can be adjusted according to the actual needs. At intervals of this time, the computer reads the distance value of a sensor.

The software only supports 16 devices.

When a single instrument is connected

The LDS Monitor tool can be used to read the "device information" of a single instrument.

It includes physical address, logical address, working mode, delay time, star distance and other parameters.

After these parameters can also be adjusted, type the parameter to write A to reset the parameters of the instrument.

Note: the above operation is actually used by address 255 to operate single instrument, and can not operate under multiple instrument networking mode. Its purpose is to detect the correctness of data, and also set the working mode and logical address function.

 

about us_Feedback_(1)