Car Bumper Repair Tool Kits Plastic Welder HPW Hot Staplers Machine Car Bumper Repair Tool Staple PVC Hot Staplers

Car Bumper Repair Tool Kits Plastic Welder HPW Hot Staplers Machine Car Bumper Repair Tool Staple PVC Hot Staplers
  • Продавецwww.tampabaybuccaneersvsminnesotavikings.us
  • Список ценUS $48.40piece
  • Продажная ценаUS $48.40piece
  • ДоставкаБесплатная доставка
  • Рейтинги3,7 (930)

Oписание продукта

HTB1whVcMXXXXXbQXFXXq6xXFXXX0AC220v 2000w hot air welder gun/hot air gun Vinyl/plastic welding gun/hot air welding machine/plastic welder

Voltage: 220V

Frequency: 50/60Hz

Power: 2000W

Adjustable temperature: 20-600°C continuously adjustable

Air flow: 13.8 m3/h

Air pressure: 3000Pa

Noise ≤65db

Package including:
(1) 1 5mm round welding mouth/tip tubular nozzle
(2) 1 40MM pressure roller
(3) 1 40mm flat nozzle

 

Products Introduction:

Hot Air Gun is double insulated,safe,reliable,steplessly adjustable and constant temperature control. It is used for hand welding on various melting plastic materials,also is used for thermoforing,docking and other operations,Normally it is used with geomembrane welding machines and handheld extrusion.

134

 

Instruction specifications:

Hot-Air Welding is used for polypropylene, polythene, PVC and polycarbonate.

The welding rod must be of the same material.

Ensure that the speed welding nozzle is clean with sharpcutting edges.

The parts to be welded must be supported in place and blocked to ensure air cannot escape through the seam.

The welding nozzle should be held so that the air slot is parallel with the seam to be welded. At the end of the weld,

the rod is cut with the cutting edge by means of a twist of the wrist. The shoe at the end of the nozzle should force

the softened welding rod into place. (fig 9)

QQ20141209114030

To weld slowly, set the heat to a lower setting.

To finish off an awkward or unsightly weld, the excess material can be cut away with a stanley knife, ground away with

a file or tooled using the gun and a cold screwdriver or chisel.

Speed Welding

The use of speed welding tips on our hot air tools increases the both the concentration of hot air and the amount of

profile welding material that can be deposited in one pass. Generally, welding with this method results in welding speeds

up to 15 times faster than pendulum welding. The welding process itself, as shown below, is the same as the pendulum

method with the exception that the speed welding nozzle is used to guide the rod onto the welding joint.

howtoweld2

 

Plastics Recognition

Take a small sliver or shaving of the material to be welded and light it with a flame, observe and smell the smoke.

· For PVC: blackish smoke and acrid smell.

· For Polyethylene (PE): no smoke, the melted material drips like candle wax and smells of wax.

· For Polypropylene (PP): no smoke, the melted material drips like candle wax and smells of burnt oil.

· For Polyamide (PA): no smoke, melted material pulls to form a thread and smells of burnt horn.

· For Polycarbonate (PC): yellowish sooty smoke, sweet smell.

· For ABS: blackish smoke, sooty flakes, sweet smell.

 

Welding Rod types & Suggested Welding Temperatures

QQ20141209114328

Application:
Application covers refuse landfill anti-seepage project, sewage disposal anti-seepage project, lake anti-seepage project, water conservancy anti-seepage project, tunnel anti-seepage project, minerals place anti-seepage project, cultivation pond anti-seepage project, roofing waterproofing project etc

Pls see the photoes of it\'s application as following:

Cautions :

1) The voltage rating stated on the tool must correspond to line/mains voltage.

2) For personal protecting on the building site, we strongly recommend the tool be connected to a GFCI (Ground Fault Circuit Interrupter) or a RCCB ( Residual Current Circuit Breaker)

3) The tool much be operated with supervision, heat can reach combustible materials which are out of sight

4) Protect tools from damp and wet